diff -urN -x CVS linux-2.6.18-rc4/arch/arm/Kconfig linux-2.6.18-rc4-at91/arch/arm/Kconfig --- linux-2.6.18-rc4/arch/arm/Kconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/Kconfig Fri Aug 11 14:55:30 2006 @@ -559,7 +567,7 @@ ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \ ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \ ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \ - ARCH_AT91RM9200 || MACH_TRIZEPS4 + ARCH_AT91 || MACH_TRIZEPS4 help If you say Y here, the LEDs on your machine will be used to provide useful information about your current system status. diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/at91rm9200dk_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/at91rm9200dk_defconfig --- linux-2.6.18-rc4/arch/arm/configs/at91rm9200dk_defconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/configs/at91rm9200dk_defconfig Fri Aug 25 10:10:17 2006 @@ -577,7 +577,7 @@ # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set -CONFIG_AT91_WATCHDOG=y +CONFIG_AT91RM9200_WATCHDOG=y # # USB-based Watchdog Cards diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/at91rm9200ek_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/at91rm9200ek_defconfig --- linux-2.6.18-rc4/arch/arm/configs/at91rm9200ek_defconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/configs/at91rm9200ek_defconfig Fri Aug 25 10:10:27 2006 @@ -558,7 +558,7 @@ # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set -CONFIG_AT91_WATCHDOG=y +CONFIG_AT91RM9200_WATCHDOG=y # # USB-based Watchdog Cards diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/at91sam9261ek_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/at91sam9261ek_defconfig --- linux-2.6.18-rc4/arch/arm/configs/at91sam9261ek_defconfig Thu Jan 1 02:00:00 1970 +++ linux-2.6.18-rc4-at91/arch/arm/configs/at91sam9261ek_defconfig Sat Aug 12 14:46:59 2006 @@ -0,0 +1,925 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.17 +# Fri Jun 30 14:57:39 2006 +# +CONFIG_ARM=y +CONFIG_MMU=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_VECTORS_BASE=0xffff0000 + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +# CONFIG_RELAY is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_UID16=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +# CONFIG_EMBEDDED is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SHMEM=y +CONFIG_SLAB=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +# CONFIG_SLOB is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +# CONFIG_BLK_DEV_IO_TRACE is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# System Type +# +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_CO285 is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_IOP3XX is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_AAEC2000 is not set +CONFIG_ARCH_AT91=y + +# +# Atmel AT91 System-on-Chip +# +# CONFIG_ARCH_AT91RM9200 is not set +CONFIG_ARCH_AT91SAM9261=y + +# +# AT91SAM9261 Board Type +# +CONFIG_MACH_AT91SAM9261EK=y + +# +# AT91 Feature Selections +# +# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_ARM926T=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5TJ=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_COPY_V4WB=y +CONFIG_CPU_TLB_V4WBI=y + +# +# Processor Features +# +# CONFIG_ARM_THUMB is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_WRITETHROUGH is not set +# CONFIG_CPU_CACHE_ROUND_ROBIN is not set + +# +# Bus support +# + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_PREEMPT is not set +# CONFIG_NO_IDLE_HZ is not set +CONFIG_HZ=100 +# CONFIG_AEABI is not set +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4096 +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw" +# CONFIG_XIP_KERNEL is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set +# CONFIG_ARTHUR is not set + +# +# Power management options +# +# CONFIG_PM is not set +# CONFIG_APM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +# CONFIG_NETDEBUG is not set +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_BIC=y +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_IEEE80211 is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set + +# +# Memory Technology Devices (MTD) +# +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +CONFIG_SCSI_MULTI_LUN=y +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_DEBUG is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# I2O device support +# + +# +# Network device support +# +# CONFIG_NETDEVICES is not set +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# PHY device support +# +# CONFIG_PHYLIB is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_SMC91X is not set +CONFIG_DM9000=y + +# +# Ethernet (1000 Mbit) +# + +# +# Ethernet (10000 Mbit) +# +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_AT91=y +CONFIG_SERIAL_AT91_CONSOLE=y +# CONFIG_SERIAL_AT91_TTYAT is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_NVRAM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_TELCLOCK is not set + +# +# I2C support +# +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Hardware Monitoring support +# +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Misc devices +# + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +CONFIG_VIDEO_V4L2=y + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set +# CONFIG_USB_DABUSB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_OHCI_HCD=y +# CONFIG_USB_OHCI_BIG_ENDIAN is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=y +CONFIG_USB_STORAGE_DEBUG=y +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_ACECAD is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_TOUCHSCREEN is not set +# CONFIG_USB_YEALINK is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set +# CONFIG_USB_ATI_REMOTE2 is not set +# CONFIG_USB_KEYSPAN_REMOTE is not set +# CONFIG_USB_APPLETOUCH is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +CONFIG_USB_MON=y + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TEST is not set + +# +# USB DSL modem support +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=y +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +CONFIG_USB_GADGET_AT91=y +CONFIG_USB_AT91=y +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=m +# CONFIG_USB_ETH is not set +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +# CONFIG_NFS_FS is not set +# CONFIG_NFSD is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=y +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_MAGIC_SYSRQ is not set +CONFIG_DEBUG_KERNEL=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_DEBUG_VM is not set +CONFIG_FRAME_POINTER=y +# CONFIG_UNWIND_INFO is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +CONFIG_DEBUG_USER=y +# CONFIG_DEBUG_WAITQ is not set +# CONFIG_DEBUG_ERRORS is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Hardware crypto devices +# + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/csb337_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/csb337_defconfig --- linux-2.6.18-rc4/arch/arm/configs/csb337_defconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/configs/csb337_defconfig Fri Aug 25 10:10:37 2006 @@ -615,7 +615,7 @@ # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set -CONFIG_AT91_WATCHDOG=y +CONFIG_AT91RM9200_WATCHDOG=y # # USB-based Watchdog Cards diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/csb637_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/csb637_defconfig --- linux-2.6.18-rc4/arch/arm/configs/csb637_defconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/configs/csb637_defconfig Fri Aug 25 10:10:48 2006 @@ -615,7 +615,7 @@ # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set -CONFIG_AT91_WATCHDOG=y +CONFIG_AT91RM9200_WATCHDOG=y # # USB-based Watchdog Cards diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/kafa_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/kafa_defconfig --- linux-2.6.18-rc4/arch/arm/configs/kafa_defconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/configs/kafa_defconfig Fri Aug 25 10:11:00 2006 @@ -560,7 +560,7 @@ # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set -CONFIG_AT91_WATCHDOG=y +CONFIG_AT91RM9200_WATCHDOG=y # CONFIG_NVRAM is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set diff -urN -x CVS linux-2.6.18-rc4/arch/arm/configs/onearm_defconfig linux-2.6.18-rc4-at91/arch/arm/configs/onearm_defconfig --- linux-2.6.18-rc4/arch/arm/configs/onearm_defconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/configs/onearm_defconfig Fri Aug 25 10:11:09 2006 @@ -607,7 +607,7 @@ # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set -CONFIG_AT91_WATCHDOG=y +CONFIG_AT91RM9200_WATCHDOG=y # # USB-based Watchdog Cards diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/Kconfig linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/Kconfig --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/Kconfig Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/Kconfig Thu Aug 10 09:42:33 2006 @@ -98,6 +98,13 @@ comment "AT91SAM9261 Board Type" +config MACH_AT91SAM9261EK + bool "Atmel AT91SAM9261-EK Evaluation Kit" + depends on ARCH_AT91SAM9261 + help + Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit. + + endif diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/Makefile linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/Makefile --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/Makefile Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/Makefile Fri Aug 11 16:27:24 2006 @@ -2,7 +2,7 @@ # Makefile for the linux kernel. # -obj-y := clock.o irq.o gpio.o devices.o +obj-y := clock.o irq.o gpio.o obj-m := obj-n := obj- := @@ -10,11 +10,11 @@ obj-$(CONFIG_PM) += pm.o # CPU-specific support -obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o -obj-$(CONFIG_ARCH_AT91SAM9260) += -obj-$(CONFIG_ARCH_AT91SAM9261) += +obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devices.o +obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o +obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o -# AT91RM9200 Board-specific support +# AT91RM9200 board-specific support obj-$(CONFIG_MACH_ONEARM) += board-1arm.o obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o @@ -28,6 +28,7 @@ # AT91SAM9260 board-specific support # AT91SAM9261 board-specific support +obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o # LEDs support led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o @@ -39,7 +40,7 @@ obj-$(CONFIG_LEDS) += $(led-y) # VGA support -#obj-$(CONFIG_FB_S1D13XXX) += ics1523.o +obj-$(CONFIG_FB_S1D13XXX) += ics1523.o ifeq ($(CONFIG_PM_DEBUG),y) diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91rm9200.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91rm9200.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91rm9200.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91rm9200.c Fri Aug 25 10:36:02 2006 @@ -16,7 +16,15 @@ #include #include +#include + #include "generic.h" +#include "clock.h" + + +/* -------------------------------------------------------------------- + * Static Memory map + * -------------------------------------------------------------------- */ static struct map_desc at91rm9200_io_desc[] __initdata = { { @@ -25,88 +33,211 @@ .length = SZ_4K, .type = MT_DEVICE, }, { - .virtual = AT91_VA_BASE_SPI, - .pfn = __phys_to_pfn(AT91_BASE_SPI), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_SSC2, - .pfn = __phys_to_pfn(AT91_BASE_SSC2), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_SSC1, - .pfn = __phys_to_pfn(AT91_BASE_SSC1), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_SSC0, - .pfn = __phys_to_pfn(AT91_BASE_SSC0), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_US3, - .pfn = __phys_to_pfn(AT91_BASE_US3), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_US2, - .pfn = __phys_to_pfn(AT91_BASE_US2), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_US1, - .pfn = __phys_to_pfn(AT91_BASE_US1), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_US0, - .pfn = __phys_to_pfn(AT91_BASE_US0), - .length = SZ_16K, - .type = MT_DEVICE, - }, { .virtual = AT91_VA_BASE_EMAC, - .pfn = __phys_to_pfn(AT91_BASE_EMAC), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_TWI, - .pfn = __phys_to_pfn(AT91_BASE_TWI), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_MCI, - .pfn = __phys_to_pfn(AT91_BASE_MCI), + .pfn = __phys_to_pfn(AT91RM9200_BASE_EMAC), .length = SZ_16K, .type = MT_DEVICE, }, { .virtual = AT91_VA_BASE_UDP, - .pfn = __phys_to_pfn(AT91_BASE_UDP), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_TCB1, - .pfn = __phys_to_pfn(AT91_BASE_TCB1), - .length = SZ_16K, - .type = MT_DEVICE, - }, { - .virtual = AT91_VA_BASE_TCB0, - .pfn = __phys_to_pfn(AT91_BASE_TCB0), + .pfn = __phys_to_pfn(AT91RM9200_BASE_UDP), .length = SZ_16K, .type = MT_DEVICE, }, { .virtual = AT91_SRAM_VIRT_BASE, - .pfn = __phys_to_pfn(AT91_SRAM_BASE), - .length = AT91_SRAM_SIZE, + .pfn = __phys_to_pfn(AT91RM9200_SRAM_BASE), + .length = AT91RM9200_SRAM_SIZE, .type = MT_DEVICE, }, }; -void __init at91rm9200_map_io(void) +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk udc_clk = { + .name = "udc_clk", + .pmc_mask = 1 << AT91RM9200_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .pmc_mask = 1 << AT91RM9200_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ether_clk = { + .name = "ether_clk", + .pmc_mask = 1 << AT91RM9200_ID_EMAC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91RM9200_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi_clk = { + .name = "twi_clk", + .pmc_mask = 1 << AT91RM9200_ID_TWI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91RM9200_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91RM9200_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91RM9200_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart3_clk = { + .name = "usart3_clk", + .pmc_mask = 1 << AT91RM9200_ID_US3, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi_clk = { + .name = "spi_clk", + .pmc_mask = 1 << AT91RM9200_ID_SPI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioC_clk = { + .name = "pioC_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioD_clk = { + .name = "pioD_clk", + .pmc_mask = 1 << AT91RM9200_ID_PIOD, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioC_clk, + &pioD_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &usart3_clk, + &mmc_clk, + &udc_clk, + &twi_clk, + &spi_clk, + // ssc 0 .. ssc2 + // tc0 .. tc5 + &ohci_clk, + ðer_clk, + // irq0 .. irq6 +}; + +/* + * The four programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; +static struct clk pck2 = { + .name = "pck2", + .pmc_mask = AT91_PMC_PCK2, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 2, +}; +static struct clk pck3 = { + .name = "pck3", + .pmc_mask = AT91_PMC_PCK3, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 3, +}; + +static void __init at91rm9200_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); + clk_register(&pck2); + clk_register(&pck3); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91rm9200_gpio[] = { + { + .id = AT91RM9200_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91RM9200_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91RM9200_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + }, { + .id = AT91RM9200_ID_PIOD, + .offset = AT91_PIOD, + .clock = &pioD_clk, + } +}; + +/* -------------------------------------------------------------------- + * AT91RM9200 processor initialization + * -------------------------------------------------------------------- */ + +void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks) { + /* Map peripherals */ iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91rm9200_register_clocks(); + + /* Register GPIO subsystem */ + at91_gpio_init(at91rm9200_gpio, banks); } + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + /* * The default interrupt priority levels (0 = lowest, 7 = highest). */ @@ -145,10 +276,14 @@ 0 /* Advanced Interrupt Controller (IRQ6) */ }; -void __init at91rm9200_init_irq(unsigned int priority[NR_AIC_IRQS]) +void __init at91rm9200_init_interrupts(unsigned int priority[NR_AIC_IRQS]) { if (!priority) priority = at91rm9200_default_irq_priority; + /* Initialize the AIC interrupt controller */ at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); } diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91rm9200_devices.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91rm9200_devices.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91rm9200_devices.c Thu Jan 1 02:00:00 1970 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91rm9200_devices.c Sat Aug 19 17:34:58 2006 @@ -0,0 +1,831 @@ +/* + * arch/arm/mach-at91rm9200/at91rm9200_devices.c + * + * Copyright (C) 2005 Thibaut VARENE + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include +#include + +#include + +#include +#include +#include + +#include "generic.h" + +#define SZ_512 0x00000200 +#define SZ_256 0x00000100 +#define SZ_16 0x00000010 + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource at91_usbh_resources[] = { + [0] = { + .start = AT91RM9200_UHP_BASE, + .end = AT91RM9200_UHP_BASE + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_UHP, + .end = AT91RM9200_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_usbh_device = { + .name = "at91_ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = at91_usbh_resources, + .num_resources = ARRAY_SIZE(at91_usbh_resources), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + if (!data) + return; + + usbh_data = *data; + platform_device_register(&at91rm9200_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource at91_udc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_UDP, + .end = AT91RM9200_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_UDP, + .end = AT91RM9200_ID_UDP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = at91_udc_resources, + .num_resources = ARRAY_SIZE(at91_udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + if (data->pullup_pin) + at91_set_gpio_output(data->pullup_pin, 0); + + udc_data = *data; + platform_device_register(&at91rm9200_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Ethernet + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE) +static u64 eth_dmamask = 0xffffffffUL; +static struct at91_eth_data eth_data; + +static struct resource at91_eth_resources[] = { + [0] = { + .start = AT91_VA_BASE_EMAC, + .end = AT91_VA_BASE_EMAC + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_EMAC, + .end = AT91RM9200_ID_EMAC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_eth_device = { + .name = "at91_ether", + .id = -1, + .dev = { + .dma_mask = ð_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = ð_data, + }, + .resource = at91_eth_resources, + .num_resources = ARRAY_SIZE(at91_eth_resources), +}; + +void __init at91_add_device_eth(struct at91_eth_data *data) +{ + if (!data) + return; + + if (data->phy_irq_pin) { + at91_set_gpio_input(data->phy_irq_pin, 0); + at91_set_deglitch(data->phy_irq_pin, 1); + } + + /* Pins used for MII and RMII */ + at91_set_A_periph(AT91_PIN_PA16, 0); /* EMDIO */ + at91_set_A_periph(AT91_PIN_PA15, 0); /* EMDC */ + at91_set_A_periph(AT91_PIN_PA14, 0); /* ERXER */ + at91_set_A_periph(AT91_PIN_PA13, 0); /* ERX1 */ + at91_set_A_periph(AT91_PIN_PA12, 0); /* ERX0 */ + at91_set_A_periph(AT91_PIN_PA11, 0); /* ECRS_ECRSDV */ + at91_set_A_periph(AT91_PIN_PA10, 0); /* ETX1 */ + at91_set_A_periph(AT91_PIN_PA9, 0); /* ETX0 */ + at91_set_A_periph(AT91_PIN_PA8, 0); /* ETXEN */ + at91_set_A_periph(AT91_PIN_PA7, 0); /* ETXCK_EREFCK */ + + if (!data->is_rmii) { + at91_set_B_periph(AT91_PIN_PB19, 0); /* ERXCK */ + at91_set_B_periph(AT91_PIN_PB18, 0); /* ECOL */ + at91_set_B_periph(AT91_PIN_PB17, 0); /* ERXDV */ + at91_set_B_periph(AT91_PIN_PB16, 0); /* ERX3 */ + at91_set_B_periph(AT91_PIN_PB15, 0); /* ERX2 */ + at91_set_B_periph(AT91_PIN_PB14, 0); /* ETXER */ + at91_set_B_periph(AT91_PIN_PB13, 0); /* ETX3 */ + at91_set_B_periph(AT91_PIN_PB12, 0); /* ETX2 */ + } + + eth_data = *data; + platform_device_register(&at91rm9200_eth_device); +} +#else +void __init at91_add_device_eth(struct at91_eth_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Compact Flash / PCMCIA + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) +static struct at91_cf_data cf_data; + +#define AT91_CF_BASE AT91_CHIPSELECT_4 + +static struct resource at91_cf_resources[] = { + [0] = { + .start = AT91_CF_BASE, + /* ties up CS4, CS5 and CS6 */ + .end = AT91_CF_BASE + (0x30000000 - 1), + .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT, + }, +}; + +static struct platform_device at91rm9200_cf_device = { + .name = "at91_cf", + .id = -1, + .dev = { + .platform_data = &cf_data, + }, + .resource = at91_cf_resources, + .num_resources = ARRAY_SIZE(at91_cf_resources), +}; + +void __init at91_add_device_cf(struct at91_cf_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->irq_pin) { + at91_set_gpio_input(data->irq_pin, 1); + at91_set_deglitch(data->irq_pin, 1); + } + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + + /* outputs, initially off */ + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + at91_set_gpio_output(data->rst_pin, 0); + + /* force poweron defaults for these pins ... */ + at91_set_A_periph(AT91_PIN_PC9, 0); /* A25/CFRNW */ + at91_set_A_periph(AT91_PIN_PC10, 0); /* NCS4/CFCS */ + at91_set_A_periph(AT91_PIN_PC11, 0); /* NCS5/CFCE1 */ + at91_set_A_periph(AT91_PIN_PC12, 0); /* NCS6/CFCE2 */ + + cf_data = *data; + platform_device_register(&at91rm9200_cf_device); +} +#else +void __init at91_add_device_cf(struct at91_cf_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MMC_AT91RM9200) || defined(CONFIG_MMC_AT91RM9200_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource at91_mmc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_MCI, + .end = AT91RM9200_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_MCI, + .end = AT91RM9200_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "at91_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = at91_mmc_resources, + .num_resources = ARRAY_SIZE(at91_mmc_resources), +}; + +void __init at91_add_device_mmc(struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_PA27, 0); + + if (data->is_b) { + /* CMD */ + at91_set_B_periph(AT91_PIN_PA8, 0); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_PA9, 0); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PA10, 0); + at91_set_B_periph(AT91_PIN_PA11, 0); + at91_set_B_periph(AT91_PIN_PA12, 0); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_PA28, 0); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_PA29, 0); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_PB3, 0); + at91_set_B_periph(AT91_PIN_PB4, 0); + at91_set_B_periph(AT91_PIN_PB5, 0); + } + } + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); +} +#else +void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +#define AT91_SMARTMEDIA_BASE AT91_CHIPSELECT_3 + +static struct resource at91_nand_resources[] = { + { + .start = AT91_SMARTMEDIA_BASE, + .end = AT91_SMARTMEDIA_BASE + SZ_8M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = at91_nand_resources, + .num_resources = ARRAY_SIZE(at91_nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + if (!data) + return; + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */ + at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */ + + nand_data = *data; + platform_device_register(&at91_nand_device); +} +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) + +static struct resource at91_twi_resources[] = { + [0] = { + .start = AT91RM9200_BASE_TWI, + .end = AT91RM9200_BASE_TWI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_TWI, + .end = AT91RM9200_ID_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_twi_device = { + .name = "at91_i2c", + .id = -1, + .resource = at91_twi_resources, + .num_resources = ARRAY_SIZE(at91_twi_resources), +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PA25, 1); + + at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PA26, 1); + + platform_device_register(&at91rm9200_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource at91_spi_resources[] = { + [0] = { + .start = AT91RM9200_BASE_SPI, + .end = AT91RM9200_BASE_SPI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_SPI, + .end = AT91RM9200_ID_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_spi_device = { + .name = "at91_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = at91_spi_resources, + .num_resources = ARRAY_SIZE(at91_spi_resources), +}; + +static const unsigned at91_spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 }; + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + + at91_set_A_periph(AT91_PIN_PA0, 0); /* MISO */ + at91_set_A_periph(AT91_PIN_PA1, 0); /* MOSI */ + at91_set_A_periph(AT91_PIN_PA2, 0); /* SPCK */ + + /* Enable SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else + cs_pin = at91_spi_standard_cs[devices[i].chip_select]; + +#ifdef CONFIG_SPI_AT91_MANUAL_CS + at91_set_gpio_output(cs_pin, 1); +#else + at91_set_A_periph(cs_pin, 0); +#endif + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + at91_clock_associate("spi_clk", &at91rm9200_spi_device.dev, "spi"); + platform_device_register(&at91rm9200_spi_device); +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif + + +/* -------------------------------------------------------------------- + * RTC + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_RTC_DRV_AT91) || defined(CONFIG_RTC_DRV_AT91_MODULE) +static struct platform_device at91rm9200_rtc_device = { + .name = "at91_rtc", + .id = -1, + .num_resources = 0, +}; + +static void __init at91_add_device_rtc(void) +{ + platform_device_register(&at91rm9200_rtc_device); +} +#else +static void __init at91_add_device_rtc(void) {} +#endif + + +/* -------------------------------------------------------------------- + * Watchdog + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_AT91_WATCHDOG) || defined(CONFIG_AT91_WATCHDOG_MODULE) +static struct platform_device at91rm9200_wdt_device = { + .name = "at91_wdt", + .id = -1, + .num_resources = 0, +}; + +static void __init at91_add_device_watchdog(void) +{ + platform_device_register(&at91rm9200_wdt_device); +} +#else +static void __init at91_add_device_watchdog(void) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SERIAL_AT91) +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_SYS, + .end = AT91RM9200_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ +}; + +static struct platform_device at91rm9200_dbgu_device = { + .name = "at91_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA30, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PA31, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US0, + .end = AT91RM9200_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US0, + .end = AT91RM9200_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart0_device = { + .name = "at91_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */ + + /* + * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21. + * We need to drive the pin manually. Default is off (RTS is active low). + */ + at91_set_gpio_output(AT91_PIN_PA21, 1); +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US1, + .end = AT91RM9200_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US1, + .end = AT91RM9200_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart1_device = { + .name = "at91_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */ + at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */ + at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */ + at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */ + at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */ + at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */ + at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US2, + .end = AT91RM9200_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US2, + .end = AT91RM9200_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart2_device = { + .name = "at91_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */ + at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */ +} + +static struct resource uart3_resources[] = { + [0] = { + .start = AT91RM9200_BASE_US3, + .end = AT91RM9200_BASE_US3 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91RM9200_ID_US3, + .end = AT91RM9200_ID_US3, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart3_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart3_device = { + .name = "at91_usart", + .id = 4, + .dev = { + .platform_data = &uart3_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart3_resources, + .num_resources = ARRAY_SIZE(uart3_resources), +}; + +static inline void configure_usart3_pins(void) +{ + at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */ + at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */ +} + +struct platform_device *at91_uarts[AT91_MAX_UART]; /* the UARTs to use */ +struct platform_device *at91_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91rm9200_uart0_device; + at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91rm9200_uart1_device; + at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91rm9200_uart2_device; + at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart"); + break; + case 3: + configure_usart3_pins(); + at91_uarts[i] = &at91rm9200_uart3_device; + at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart"); + break; + case 4: + configure_dbgu_pins(); + at91_uarts[i] = &at91rm9200_dbgu_device; + at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < AT91_MAX_UART) + at91_default_console_device = at91_uarts[config->console_tty]; + if (!at91_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < AT91_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ + +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + at91_add_device_rtc(); + at91_add_device_watchdog(); + return 0; +} + +arch_initcall(at91_add_standard_devices); diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91rm9200_time.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91rm9200_time.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91rm9200_time.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91rm9200_time.c Thu Aug 10 08:49:11 2006 @@ -113,7 +113,7 @@ (void) at91_sys_read(AT91_ST_SR); /* Clear any pending interrupts */ /* Make IRQs happen for the system timer */ - setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq); + setup_irq(AT91RM9200_ID_SYS, &at91rm9200_timer_irq); /* Change the kernel's 'tick' value to 10009 usec. (the default is 10000) */ tick_usec = (LATCH * 1000000) / CLOCK_TICK_RATE; diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91sam9261.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91sam9261.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91sam9261.c Thu Jan 1 02:00:00 1970 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91sam9261.c Fri Aug 25 10:36:19 2006 @@ -0,0 +1,268 @@ +/* + * arch/arm/mach-at91rm9200/at91sam9261.c + * + * Copyright (C) 2005 SAN People + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ + +#include + +#include +#include + +#include +#include + +#include "generic.h" +#include "clock.h" + +static struct map_desc at91sam9261_io_desc[] __initdata = { + { + .virtual = AT91_VA_BASE_SYS, + .pfn = __phys_to_pfn(AT91SAM9261_BASE_SYS), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_VA_BASE_UDP, + .pfn = __phys_to_pfn(AT91SAM9261_BASE_UDP), + .length = SZ_16K, + .type = MT_DEVICE, + }, { + .virtual = AT91_SRAM_VIRT_BASE, + .pfn = __phys_to_pfn(AT91SAM9261_SRAM_BASE), + .length = AT91SAM9261_SRAM_SIZE, + .type = MT_DEVICE, + }, +}; + +/* -------------------------------------------------------------------- + * Clocks + * -------------------------------------------------------------------- */ + +/* + * The peripheral clocks. + */ +static struct clk udc_clk = { + .name = "udc_clk", + .pmc_mask = 1 << AT91SAM9261_ID_UDP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk ohci_clk = { + .name = "ohci_clk", + .pmc_mask = 1 << AT91SAM9261_ID_UHP, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk mmc_clk = { + .name = "mci_clk", + .pmc_mask = 1 << AT91SAM9261_ID_MCI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk twi_clk = { + .name = "twi_clk", + .pmc_mask = 1 << AT91SAM9261_ID_TWI, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart0_clk = { + .name = "usart0_clk", + .pmc_mask = 1 << AT91SAM9261_ID_US0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart1_clk = { + .name = "usart1_clk", + .pmc_mask = 1 << AT91SAM9261_ID_US1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk usart2_clk = { + .name = "usart2_clk", + .pmc_mask = 1 << AT91SAM9261_ID_US2, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi0_clk = { + .name = "spi0_clk", + .pmc_mask = 1 << AT91SAM9261_ID_SPI0, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk spi1_clk = { + .name = "spi0_clk", + .pmc_mask = 1 << AT91SAM9261_ID_SPI1, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioA_clk = { + .name = "pioA_clk", + .pmc_mask = 1 << AT91SAM9261_ID_PIOA, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioB_clk = { + .name = "pioB_clk", + .pmc_mask = 1 << AT91SAM9261_ID_PIOB, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk pioC_clk = { + .name = "pioC_clk", + .pmc_mask = 1 << AT91SAM9261_ID_PIOC, + .type = CLK_TYPE_PERIPHERAL, +}; +static struct clk lcdc_clk = { + .name = "lcdc_clk", + .pmc_mask = 1 << AT91SAM9261_ID_LCDC, + .type = CLK_TYPE_PERIPHERAL, +}; + +static struct clk *periph_clocks[] __initdata = { + &pioA_clk, + &pioB_clk, + &pioC_clk, + &usart0_clk, + &usart1_clk, + &usart2_clk, + &mmc_clk, + &udc_clk, + &twi_clk, + &spi0_clk, + &spi1_clk, + // ssc 0 .. ssc2 + // tc0 .. tc2 + &ohci_clk, + &lcdc_clk, + // irq0 .. irq2 +}; + +/* + * The four programmable clocks. + * You must configure pin multiplexing to bring these signals out. + */ +static struct clk pck0 = { + .name = "pck0", + .pmc_mask = AT91_PMC_PCK0, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 0, +}; +static struct clk pck1 = { + .name = "pck1", + .pmc_mask = AT91_PMC_PCK1, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 1, +}; +static struct clk pck2 = { + .name = "pck2", + .pmc_mask = AT91_PMC_PCK2, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 2, +}; +static struct clk pck3 = { + .name = "pck3", + .pmc_mask = AT91_PMC_PCK3, + .type = CLK_TYPE_PROGRAMMABLE, + .id = 3, +}; + +static void __init at91sam9261_register_clocks(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(periph_clocks); i++) + clk_register(periph_clocks[i]); + + clk_register(&pck0); + clk_register(&pck1); + clk_register(&pck2); + clk_register(&pck3); +} + +/* -------------------------------------------------------------------- + * GPIO + * -------------------------------------------------------------------- */ + +static struct at91_gpio_bank at91sam9261_gpio[] = { + { + .id = AT91SAM9261_ID_PIOA, + .offset = AT91_PIOA, + .clock = &pioA_clk, + }, { + .id = AT91SAM9261_ID_PIOB, + .offset = AT91_PIOB, + .clock = &pioB_clk, + }, { + .id = AT91SAM9261_ID_PIOC, + .offset = AT91_PIOC, + .clock = &pioC_clk, + } +}; + +/* -------------------------------------------------------------------- + * AT91SAM9261 processor initialization + * -------------------------------------------------------------------- */ + +void __init at91sam9261_initialize(unsigned long main_clock) +{ + /* Map peripherals */ + iotable_init(at91sam9261_io_desc, ARRAY_SIZE(at91sam9261_io_desc)); + + /* Init clock subsystem */ + at91_clock_init(main_clock); + + /* Register the processor-specific clocks */ + at91sam9261_register_clocks(); + + /* Register GPIO subsystem */ + at91_gpio_init(at91sam9261_gpio, 3); +} + +/* -------------------------------------------------------------------- + * Interrupt initialization + * -------------------------------------------------------------------- */ + +/* + * The default interrupt priority levels (0 = lowest, 7 = highest). + */ +static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = { + 7, /* Advanced Interrupt Controller */ + 7, /* System Peripherals */ + 0, /* Parallel IO Controller A */ + 0, /* Parallel IO Controller B */ + 0, /* Parallel IO Controller C */ + 0, + 6, /* USART 0 */ + 6, /* USART 1 */ + 6, /* USART 2 */ + 0, /* Multimedia Card Interface */ + 4, /* USB Device Port */ + 0, /* Two-Wire Interface */ + 6, /* Serial Peripheral Interface 0 */ + 6, /* Serial Peripheral Interface 1 */ + 5, /* Serial Synchronous Controller 0 */ + 5, /* Serial Synchronous Controller 1 */ + 5, /* Serial Synchronous Controller 2 */ + 0, /* Timer Counter 0 */ + 0, /* Timer Counter 1 */ + 0, /* Timer Counter 2 */ + 3, /* USB Host port */ + 3, /* LCD Controller */ + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ + 0, /* Advanced Interrupt Controller */ +}; + +void __init at91sam9261_init_irq(unsigned int priority[NR_AIC_IRQS]) +{ + if (!priority) + priority = at91sam9261_default_irq_priority; + + /* Initialize the AIC interrupt controller */ + at91_aic_init(priority); + + /* Enable GPIO interrupts */ + at91_gpio_irq_setup(); +} diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91sam9261_devices.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91sam9261_devices.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91sam9261_devices.c Thu Jan 1 02:00:00 1970 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91sam9261_devices.c Sat Aug 19 17:35:20 2006 @@ -0,0 +1,678 @@ +/* + * arch/arm/mach-at91rm9200/at91sam9261_devices.c + * + * Copyright (C) 2005 Thibaut VARENE + * Copyright (C) 2005 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + */ +#include +#include + +#include + +#include +#include +#include +#include + +#include "generic.h" + +#define SZ_512 0x00000200 +#define SZ_256 0x00000100 +#define SZ_16 0x00000010 + +/* -------------------------------------------------------------------- + * USB Host + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +static u64 ohci_dmamask = 0xffffffffUL; +static struct at91_usbh_data usbh_data; + +static struct resource at91_usbh_resources[] = { + [0] = { + .start = AT91SAM9261_UHP_BASE, + .end = AT91SAM9261_UHP_BASE + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_UHP, + .end = AT91SAM9261_ID_UHP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_usbh_device = { + .name = "at91_ohci", + .id = -1, + .dev = { + .dma_mask = &ohci_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &usbh_data, + }, + .resource = at91_usbh_resources, + .num_resources = ARRAY_SIZE(at91_usbh_resources), +}; + +void __init at91_add_device_usbh(struct at91_usbh_data *data) +{ + if (!data) + return; + + usbh_data = *data; + platform_device_register(&at91rm9200_usbh_device); +} +#else +void __init at91_add_device_usbh(struct at91_usbh_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * USB Device (Gadget) + * -------------------------------------------------------------------- */ + +#ifdef CONFIG_USB_GADGET_AT91 +static struct at91_udc_data udc_data; + +static struct resource at91_udc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_UDP, + .end = AT91SAM9261_BASE_UDP + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_UDP, + .end = AT91SAM9261_ID_UDP, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_udc_device = { + .name = "at91_udc", + .id = -1, + .dev = { + .platform_data = &udc_data, + }, + .resource = at91_udc_resources, + .num_resources = ARRAY_SIZE(at91_udc_resources), +}; + +void __init at91_add_device_udc(struct at91_udc_data *data) +{ + if (!data) + return; + + if (data->vbus_pin) { + at91_set_gpio_input(data->vbus_pin, 0); + at91_set_deglitch(data->vbus_pin, 1); + } + + /* Pullup-pin is handled internally */ +#warning "Insert matrix code here" + + udc_data = *data; + platform_device_register(&at91rm9200_udc_device); +} +#else +void __init at91_add_device_udc(struct at91_udc_data *data) {} +#endif + + +/* -------------------------------------------------------------------- + * Compact Flash / PCMCIA + * -------------------------------------------------------------------- */ + +#if 0 +#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) +static struct at91_cf_data cf_data; + +static struct resource at91_cf_resources[] = { + [0] = { + .start = AT91SAM9261_CF_BASE, + /* ties up CS4, CS5 and CS6 */ + .end = AT91SAM9261_CF_BASE + (0x30000000 - 1), + .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT, + }, +}; + +static struct platform_device at91rm9200_cf_device = { + .name = "at91_cf", + .id = -1, + .dev = { + .platform_data = &cf_data, + }, + .resource = at91_cf_resources, + .num_resources = ARRAY_SIZE(at91_cf_resources), +}; + +void __init at91_add_device_cf(struct at91_cf_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->irq_pin) { + at91_set_gpio_input(data->irq_pin, 1); + at91_set_deglitch(data->irq_pin, 1); + } + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + + /* outputs, initially off */ + if (data->vcc_pin) + at91_set_gpio_output(data->vcc_pin, 0); + at91_set_gpio_output(data->rst_pin, 0); + + /* force poweron defaults for these pins ... */ + at91_set_A_periph(AT91_PIN_, 0); /* A25/CFRNW */ + at91_set_A_periph(AT91_PIN_, 0); /* NCS4/CFCS */ + at91_set_A_periph(AT91_PIN_, 0); /* NCS5/CFCE1 */ + at91_set_A_periph(AT91_PIN_, 0); /* NCS6/CFCE2 */ + + cf_data = *data; + platform_device_register(&at91rm9200_cf_device); +} +#else +void __init at91_add_device_cf(struct at91_cf_data *data) {} +#endif +#endif + + +/* -------------------------------------------------------------------- + * MMC / SD + * -------------------------------------------------------------------- */ + +#if 0 +#if defined(CONFIG_MMC_AT91RM9200) || defined(CONFIG_MMC_AT91RM9200_MODULE) +static u64 mmc_dmamask = 0xffffffffUL; +static struct at91_mmc_data mmc_data; + +static struct resource at91_mmc_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_MCI, + .end = AT91SAM9261_BASE_MCI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_MCI, + .end = AT91SAM9261_ID_MCI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_mmc_device = { + .name = "at91_mci", + .id = -1, + .dev = { + .dma_mask = &mmc_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &mmc_data, + }, + .resource = at91_mmc_resources, + .num_resources = ARRAY_SIZE(at91_mmc_resources), +}; + +void __init at91_add_device_mmc(struct at91_mmc_data *data) +{ + if (!data) + return; + + /* input/irq */ + if (data->det_pin) { + at91_set_gpio_input(data->det_pin, 1); + at91_set_deglitch(data->det_pin, 1); + } + if (data->wp_pin) + at91_set_gpio_input(data->wp_pin, 1); + + /* CLK */ + at91_set_A_periph(AT91_PIN_, 0); + + if (data->is_b) { + /* CMD */ + at91_set_B_periph(AT91_PIN_, 0); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_B_periph(AT91_PIN_, 0); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_, 0); + at91_set_B_periph(AT91_PIN_, 0); + at91_set_B_periph(AT91_PIN_, 0); + } + } else { + /* CMD */ + at91_set_A_periph(AT91_PIN_, 0); + + /* DAT0, maybe DAT1..DAT3 */ + at91_set_A_periph(AT91_PIN_, 0); + if (data->wire4) { + at91_set_B_periph(AT91_PIN_, 0); + at91_set_B_periph(AT91_PIN_, 0); + at91_set_B_periph(AT91_PIN_, 0); + } + } + + mmc_data = *data; + platform_device_register(&at91rm9200_mmc_device); +} +#else +void __init at91_add_device_mmc(struct at91_mmc_data *data) {} +#endif +#endif + + +/* -------------------------------------------------------------------- + * NAND / SmartMedia + * -------------------------------------------------------------------- */ + +#if 0 +#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) +static struct at91_nand_data nand_data; + +static struct resource at91_nand_resources[] = { + { + .start = AT91SAM9261_SMARTMEDIA_BASE, + .end = AT91SAM9261_SMARTMEDIA_BASE + SZ_8M - 1, + .flags = IORESOURCE_MEM, + } +}; + +static struct platform_device at91_nand_device = { + .name = "at91_nand", + .id = -1, + .dev = { + .platform_data = &nand_data, + }, + .resource = at91_nand_resources, + .num_resources = ARRAY_SIZE(at91_nand_resources), +}; + +void __init at91_add_device_nand(struct at91_nand_data *data) +{ + if (!data) + return; + + /* enable pin */ + if (data->enable_pin) + at91_set_gpio_output(data->enable_pin, 1); + + /* ready/busy pin */ + if (data->rdy_pin) + at91_set_gpio_input(data->rdy_pin, 1); + + /* card detect pin */ + if (data->det_pin) + at91_set_gpio_input(data->det_pin, 1); + + at91_set_A_periph(AT91_PIN_, 0); /* SMOE */ + at91_set_A_periph(AT91_PIN_, 0); /* SMWE */ + + nand_data = *data; + platform_device_register(&at91_nand_device); +} +#else +void __init at91_add_device_nand(struct at91_nand_data *data) {} +#endif +#endif + + +/* -------------------------------------------------------------------- + * TWI (i2c) + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE) +static struct platform_device at91rm9200_twi_device = { + .name = "at91_i2c", + .id = -1, + .num_resources = 0, +}; + +void __init at91_add_device_i2c(void) +{ + /* pins used for TWI interface */ + at91_set_A_periph(AT91_PIN_PA7, 0); /* TWD */ + at91_set_multi_drive(AT91_PIN_PA7, 1); + + at91_set_A_periph(AT91_PIN_PA8, 0); /* TWCK */ + at91_set_multi_drive(AT91_PIN_PA8, 1); + + platform_device_register(&at91rm9200_twi_device); +} +#else +void __init at91_add_device_i2c(void) {} +#endif + + +/* -------------------------------------------------------------------- + * SPI + * -------------------------------------------------------------------- */ + +#if 0 +#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) +static u64 spi_dmamask = 0xffffffffUL; + +static struct resource at91_spi_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_SPI, + .end = AT91SAM9261_BASE_SPI + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_SPI, + .end = AT91SAM9261_ID_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device at91rm9200_spi_device = { + .name = "at91_spi", + .id = 0, + .dev = { + .dma_mask = &spi_dmamask, + .coherent_dma_mask = 0xffffffff, + }, + .resource = at91_spi_resources, + .num_resources = ARRAY_SIZE(at91_spi_resources), +}; + +static const unsigned at91_spi0_standard_cs[4] = { AT91_PIN_, AT91_PIN_, AT91_PIN_, AT91_PIN_ }; +static const unsigned at91_spi1_standard_cs[4] = { AT91_PIN_, AT91_PIN_, AT91_PIN_, AT91_PIN_ }; + +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) +{ + int i; + unsigned long cs_pin; + + at91_set_A_periph(AT91_PIN_, 0); /* MISO */ + at91_set_A_periph(AT91_PIN_, 0); /* MOSI */ + at91_set_A_periph(AT91_PIN_, 0); /* SPCK */ + + /* Enable SPI chip-selects */ + for (i = 0; i < nr_devices; i++) { + if (devices[i].controller_data) + cs_pin = (unsigned long) devices[i].controller_data; + else + cs_pin = at91_spi_standard_cs[devices[i].chip_select]; + +#ifdef CONFIG_SPI_AT91_MANUAL_CS + at91_set_gpio_output(cs_pin, 1); +#else + at91_set_A_periph(cs_pin, 0); +#endif + + /* pass chip-select pin to driver */ + devices[i].controller_data = (void *) cs_pin; + } + + spi_register_board_info(devices, nr_devices); + at91_clock_associate("spi0_clk", &at91rm9200_spi_device.dev, "spi"); + platform_device_register(&at91rm9200_spi_device); +} +#else +void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {} +#endif +#endif + + +/* -------------------------------------------------------------------- + * Watchdog + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_AT91_WATCHDOG) || defined(CONFIG_AT91_WATCHDOG_MODULE) +static struct platform_device at91rm9200_wdt_device = { + .name = "at91sam9_wdt", + .id = -1, + .num_resources = 0, +}; + +static void __init at91_add_device_watchdog(void) +{ + platform_device_register(&at91rm9200_wdt_device); +} +#else +static void __init at91_add_device_watchdog(void) {} +#endif + + +/* -------------------------------------------------------------------- + * LEDs + * -------------------------------------------------------------------- */ + +#if 0 +#if defined(CONFIG_LEDS) +u8 at91_leds_cpu; +u8 at91_leds_timer; + +void __init at91_init_leds(u8 cpu_led, u8 timer_led) +{ + at91_leds_cpu = cpu_led; + at91_leds_timer = timer_led; +} +#else +void __init at91_init_leds(u8 cpu_led, u8 timer_led) {} +#endif +#endif + + +/* -------------------------------------------------------------------- + * UART + * -------------------------------------------------------------------- */ + +#if defined(CONFIG_SERIAL_AT91) +static struct resource dbgu_resources[] = { + [0] = { + .start = AT91_VA_BASE_SYS + AT91_DBGU, + .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_SYS, + .end = AT91SAM9261_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data dbgu_data = { + .use_dma_tx = 0, + .use_dma_rx = 0, /* DBGU not capable of receive DMA */ +}; + +static struct platform_device at91rm9200_dbgu_device = { + .name = "at91_usart", + .id = 0, + .dev = { + .platform_data = &dbgu_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = dbgu_resources, + .num_resources = ARRAY_SIZE(dbgu_resources), +}; + +static inline void configure_dbgu_pins(void) +{ + at91_set_A_periph(AT91_PIN_PA9, 0); /* DRXD */ + at91_set_A_periph(AT91_PIN_PA10, 1); /* DTXD */ +} + +static struct resource uart0_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_US0, + .end = AT91SAM9261_BASE_US0 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_US0, + .end = AT91SAM9261_ID_US0, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart0_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart0_device = { + .name = "at91_usart", + .id = 1, + .dev = { + .platform_data = &uart0_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart0_resources, + .num_resources = ARRAY_SIZE(uart0_resources), +}; + +static inline void configure_usart0_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC8, 1); /* TXD0 */ + at91_set_A_periph(AT91_PIN_PC9, 0); /* RXD0 */ + at91_set_A_periph(AT91_PIN_PC10, 0); /* RTS0 */ + at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS0 */ +} + +static struct resource uart1_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_US1, + .end = AT91SAM9261_BASE_US1 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_US1, + .end = AT91SAM9261_ID_US1, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart1_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart1_device = { + .name = "at91_usart", + .id = 2, + .dev = { + .platform_data = &uart1_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart1_resources, + .num_resources = ARRAY_SIZE(uart1_resources), +}; + +static inline void configure_usart1_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC12, 1); /* TXD1 */ + at91_set_A_periph(AT91_PIN_PC13, 0); /* RXD1 */ +} + +static struct resource uart2_resources[] = { + [0] = { + .start = AT91SAM9261_BASE_US2, + .end = AT91SAM9261_BASE_US2 + SZ_16K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91SAM9261_ID_US2, + .end = AT91SAM9261_ID_US2, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct at91_uart_data uart2_data = { + .use_dma_tx = 1, + .use_dma_rx = 1, +}; + +static struct platform_device at91rm9200_uart2_device = { + .name = "at91_usart", + .id = 3, + .dev = { + .platform_data = &uart2_data, + .coherent_dma_mask = 0xffffffff, + }, + .resource = uart2_resources, + .num_resources = ARRAY_SIZE(uart2_resources), +}; + +static inline void configure_usart2_pins(void) +{ + at91_set_A_periph(AT91_PIN_PC15, 0); /* RXD2 */ + at91_set_A_periph(AT91_PIN_PC14, 1); /* TXD2 */ +} + +struct platform_device *at91_uarts[AT91_MAX_UART]; /* the UARTs to use */ +struct platform_device *at91_default_console_device; /* the serial console device */ + +void __init at91_init_serial(struct at91_uart_config *config) +{ + int i; + + /* Fill in list of supported UARTs */ + for (i = 0; i < config->nr_tty; i++) { + switch (config->tty_map[i]) { + case 0: + configure_usart0_pins(); + at91_uarts[i] = &at91rm9200_uart0_device; + at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart"); + break; + case 1: + configure_usart1_pins(); + at91_uarts[i] = &at91rm9200_uart1_device; + at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart"); + break; + case 2: + configure_usart2_pins(); + at91_uarts[i] = &at91rm9200_uart2_device; + at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart"); + break; + case 3: + configure_dbgu_pins(); + at91_uarts[i] = &at91rm9200_dbgu_device; + at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart"); + break; + default: + continue; + } + at91_uarts[i]->id = i; /* update ID number to mapped ID */ + } + + /* Set serial console device */ + if (config->console_tty < AT91_MAX_UART) + at91_default_console_device = at91_uarts[config->console_tty]; + if (!at91_default_console_device) + printk(KERN_INFO "AT91: No default serial console defined.\n"); +} + +void __init at91_add_device_serial(void) +{ + int i; + + for (i = 0; i < AT91_MAX_UART; i++) { + if (at91_uarts[i]) + platform_device_register(at91_uarts[i]); + } +} +#else +void __init at91_init_serial(struct at91_uart_config *config) {} +void __init at91_add_device_serial(void) {} +#endif + + +/* -------------------------------------------------------------------- */ + +/* + * These devices are always present and don't need any board-specific + * setup. + */ +static int __init at91_add_standard_devices(void) +{ + return 0; +} + +arch_initcall(at91_add_standard_devices); diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91sam926x_time.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91sam926x_time.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/at91sam926x_time.c Thu Jan 1 02:00:00 1970 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/at91sam926x_time.c Wed Aug 16 10:14:28 2006 @@ -0,0 +1,115 @@ +/* + * linux/arch/arm/mach-at91rm9200/at91sam926x_time.c + * + * Copyright (C) 2005-2006 M. Amine SAYA, ATMEL Rousset, France + * Revision 2005 M. Nicolas Diremdjian, ATMEL Rousset, France + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include +#include + + +#define PIT_CPIV(x) ((x) & AT91_PIT_CPIV) +#define PIT_PICNT(x) (((x) & AT91_PIT_PICNT) >> 20) + +/* + * Returns number of microseconds since last timer interrupt. Note that interrupts + * will have been disabled by do_gettimeofday() + * 'LATCH' is hwclock ticks (see CLOCK_TICK_RATE in timex.h) per jiffy. + * 'tick' is usecs per jiffy (linux/timex.h). + */ +static unsigned long at91sam926x_gettimeoffset(void) +{ + unsigned long elapsed; + unsigned long t = at91_sys_read(AT91_PIT_PIIR); + + elapsed = (PIT_PICNT(t) * LATCH) + PIT_CPIV(t); /* hardware clock cycles */ + + return (unsigned long)(elapsed * 1000000) / LATCH; +} + +/* + * IRQ handler for the timer. + */ +static irqreturn_t at91sam926x_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + volatile long nr_ticks; + + if (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS) { /* This is a shared interrupt */ + write_seqlock(&xtime_lock); + + /* Get number to ticks performed before interrupt and clear PIT interrupt */ + nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); + do { + timer_tick(regs); + nr_ticks--; + } while (nr_ticks); + + write_sequnlock(&xtime_lock); + return IRQ_HANDLED; + } else + return IRQ_NONE; /* not handled */ +} + +static struct irqaction at91sam926x_timer_irq = { + .name = "at91_tick", + .flags = IRQF_SHARED | IRQF_DISABLED | IRQF_TIMER, + .handler = at91sam926x_timer_interrupt +}; + +void at91sam926x_timer_reset(void) +{ + /* Disable timer */ + at91_sys_write(AT91_PIT_MR, 0); + + /* Clear any pending interrupts */ + (void) at91_sys_read(AT91_PIT_PIVR); + + /* Set Period Interval timer and enable its interrupt */ + at91_sys_write(AT91_PIT_MR, (LATCH & AT91_PIT_PIV) | AT91_PIT_PITIEN | AT91_PIT_PITEN); +} + +/* + * Set up timer interrupt. + */ +void __init at91sam926x_timer_init(void) +{ + /* Initialize and enable the timer */ + at91sam926x_timer_reset(); + + /* Make IRQs happen for the system timer. */ + setup_irq(AT91SAM9261_ID_SYS, &at91sam926x_timer_irq); +} + +#ifdef CONFIG_PM +static void at91sam926x_timer_suspend(void) +{ + /* Disable timer */ + at91_sys_write(AT91_PIT_MR, 0); +} +#else +#define at91sam926x_timer_suspend NULL +#endif + +struct sys_timer at91sam926x_timer = { + .init = at91sam926x_timer_init, + .offset = at91sam926x_gettimeoffset, + .suspend = at91sam926x_timer_suspend, + .resume = at91sam926x_timer_reset, +}; + diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-1arm.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-1arm.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-1arm.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-1arm.c Fri Aug 11 18:21:46 2006 @@ -34,20 +34,11 @@ #include #include -#include #include #include #include "generic.h" -static void __init onearm_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(PQFP_GPIO_BANKS); -} /* * Serial port configuration. @@ -62,15 +53,18 @@ static void __init onearm_map_io(void) { - at91rm9200_map_io(); - - /* Initialize clocks: 18.432 MHz crystal */ - at91_clock_init(18432000); + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_PQFP); /* Setup the serial ports and console */ at91_init_serial(&onearm_uart_config); } +static void __init onearm_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata onearm_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-carmeva.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-carmeva.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-carmeva.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-carmeva.c Fri Aug 11 18:22:02 2006 @@ -35,20 +35,11 @@ #include #include -#include #include #include #include "generic.h" -static void __init carmeva_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -63,15 +54,18 @@ static void __init carmeva_map_io(void) { - at91rm9200_map_io(); - - /* Initialize clocks: 20.000 MHz crystal */ - at91_clock_init(20000000); + /* Initialize processor: 20.000 MHz crystal */ + at91rm9200_initialize(20000000, AT91RM9200_BGA); /* Setup the serial ports and console */ at91_init_serial(&carmeva_uart_config); } +static void __init carmeva_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata carmeva_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-csb337.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-csb337.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-csb337.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-csb337.c Fri Aug 11 18:22:25 2006 @@ -34,20 +34,11 @@ #include #include -#include #include #include #include "generic.h" -static void __init csb337_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -62,10 +53,8 @@ static void __init csb337_map_io(void) { - at91rm9200_map_io(); - - /* Initialize clocks: 3.6864 MHz crystal */ - at91_clock_init(3686400); + /* Initialize processor: 3.6864 MHz crystal */ + at91rm9200_initialize(3686400, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); @@ -74,6 +63,11 @@ at91_init_serial(&csb337_uart_config); } +static void __init csb337_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata csb337_eth_data = { .phy_irq_pin = AT91_PIN_PC2, .is_rmii = 0, diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-csb637.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-csb637.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-csb637.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-csb637.c Fri Aug 11 18:22:38 2006 @@ -33,20 +33,11 @@ #include #include -#include #include #include #include "generic.h" -static void __init csb637_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -61,10 +52,8 @@ static void __init csb637_map_io(void) { - at91rm9200_map_io(); - - /* Initialize clocks: 3.6864 MHz crystal */ - at91_clock_init(3686400); + /* Initialize processor: 3.6864 MHz crystal */ + at91rm9200_initialize(3686400, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); @@ -73,6 +62,11 @@ at91_init_serial(&csb637_uart_config); } +static void __init csb637_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + static struct at91_eth_data __initdata csb637_eth_data = { .phy_irq_pin = AT91_PIN_PC0, .is_rmii = 0, diff -urN -x CVS linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-dk.c linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-dk.c --- linux-2.6.18-rc4/arch/arm/mach-at91rm9200/board-dk.c Fri Aug 25 10:49:30 2006 +++ linux-2.6.18-rc4-at91/arch/arm/mach-at91rm9200/board-dk.c Sat Aug 12 14:44:54 2006 @@ -37,20 +37,11 @@ #include #include -#include #include #include #include "generic.h" -static void __init dk_init_irq(void) -{ - /* Initialize AIC controller */ - at91rm9200_init_irq(NULL); - - /* Set up the GPIO interrupts */ - at91_gpio_irq_setup(BGA_GPIO_BANKS); -} /* * Serial port configuration. @@ -65,10 +56,8 @@ static void __init dk_map_io(void) { - at91rm9200_map_io(); - - /* Initialize clocks: 18.432 MHz crystal */ - at91_clock_init(18432000); + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_BGA); /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); @@ -77,6 +66,190 @@ at91_init_serial(&dk_uart_config); } +static void __init dk_init_irq(void) +{ + at91rm9200_init_interrupts(NULL); +} + +#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE) +#include